CCNP Routing and Switching Solved MCQ
CCNP Routing and Switching Solved MCQ contain set of 10 MCQ questions for CCNP MCQ which will help you to clear beginner level quiz.
1. Question:–Loopguard should be enabled on designated ports and Rootguard should be enabled on blocking ports
a. No – Loopguard and Rootguard should be enabled on the same ports
b. No – Loopguard should be enabled on blocking ports on Rootguard should be enabled on designated ports
c. Yes – Loopguard should be enabled on designated ports and Rootguard should be enabled on blocking ports
d. No – if Rootguard is configured on the switch, Loopguard can not be enabled and vice versa
2. Question:—To debug VTP events, the following command needs to be issued:
a. debug switchport <interface name/number> vtp events
b. debug vtp events
c. debug sw-vlan vtp events
3. Question:—Native VLAN mismatch detection is provided by the 802.1Q protocol
a. True
b. False
4. Question:—Which of the following statements are false about “Non stop forwarding” (NSF) (select three answers)
a. Routing protocols do not require any special configuration to utilize NSF
b. NSF can be used with RPR
c. NSF is supported with OSPF, BGP, RIP and EIGRP.
d. The main objective of NSF is to keep forwarding packets after a route processor failover
e. NSF relies on CEF for packet forwarding while RIB is being rebuilt after a failure
f. To run NSF, both supervisors need an identical IOS image
5. Question:—Which of the following would likely result in a CEF punt: (select three answers)
a. A “loose source” IP option is present in the IP header
b. There are multiple entries in the FIB table for the particular destination
c. An access list with the “log” option is configured on the router and the incoming traffic matches the access list.
d. A default route would need to be used to forward the traffic
e. The destination network is known by both OSPF and EIGRP
f. Administrator uses ping to verify the reachability of the router in question
6. Question:—Which statements about Multiple Spanning Tree (MST) are true: (select two answers)
a. Cisco switches support up to 15 MSTIs and 1 IST
b. The aim of running MST is to have one instance of STP per each VLAN
c. Cisco switches support up to 16 MSTIs and 1 IST
d. VTP can be used to propagate the VLAN to instance mappings
e. VTP can not be used to propagate the VLAN to instance mappings, this has to be done manually on each switch
7. Question:—-Changing VTP mode from Server to Client will delete the existing VLANS
a. No
b. Yes
8. Question:—-Which of the following switching methods is the most widely supported across different Cisco hardware and IOS software images:
a. Interrupt Context Switching
b. Optimum switching
c. CEF
d. Process switching
9. Question:—-You must configure “vtp pruning” on all switches in the domain
a. No – This command only needs to be issued on one of the servers. This change will then be propagated throughout the domain.
b. No – This command only needs to be issued on one of the servers or clients. This change will then be propagated throughout the domain.
c. Yes – pruning is not an extension to the VTP protocol, therefore needs to be configured manually on all servers in the VTP domain
10. Question:—Issuing “spanning-tree uplinkfast” increases the priority of the switch amongst other changes in the configuration.
a. No – this command reduces the priority
b. Yes – this command increases the priority
11. Question:—Which statements about First Hop Redundancy Protocols (FHRP) are false (select three answers):
a. Preemption is enabled by default when using HSRP and GLBP. It is disabled by default, if VRRP is used.
b. The virtual IP address of VRRP group can be configured with the same IP address as for one of the physical router interfaces in the group
c. FHRP protocols can be enabled on both L2 and L3 interfaces
d. Only GLBP offers load balancing between multiple routers in the group
e. HSRP priority uses the same concept as STP bridge priority – interface with lower value priority has more chance to become the primary router